ReferenceDesignLibrary

Refine Search

Eval Board Voltage In Topology Current Out Voltage Out (Max) Outputs and Type Efficiency @ Conditions Features Switching Frequency Component Count + Extras Design Author Application / Target Market Main I.C. Base Part
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear All Selections Apply Filters

Designs (152)

152 Results - Page 1/16 |< < 1 2 3 4 5 > >|

LM3401-MR16DEMO: 1A @ 6.2V Max, 12VAC, MR16

Manufacturer: Texas Instruments

This design was developed to minimize the current spikes coming out of an electronic transformer to less than 5A, which is a typical transformer rating, when driving an LED MR16 circuit. The off the shelf LED MR16 solutions exhibit spikes that significantly exceed a transformers maximum rated output current which will degrade the reliability of the transformer and reduce its operating lifetime. T…

View Design

LM3464EVAL: 4 Channel @ 350 mA/chan, 12~80V in

Manufacturer: Texas Instruments

This evaluation board demonstrates the high power efficiency and outstanding output current accuracy of the LM3464A typical application circuit. With four LED strings connected, the total output power is about 50W. The schematic, bill of material and PCB layout drawing of the LM3464A evaluation board are provided in this document.

View Design

NCP3065D1SLDGEVB: 0.35, 0.7, or 1A @ 23V Max, 8 ~ 20V in

Manufacturer: ON Semiconductor

The NCP3065 is a monolithic switching regulator designed to deliver constant current for powering high brightness LEDs. The device has a very low feedback voltage of 235 mV (nominal) which is used to regulate the average current of the LED string. In addition, the NCP3065 has a wide input voltage up to 40 V to allow it to operate from 12 Vac or 12 Vdc supplies commonly used for lighting applicati…

View Design

EVL6562A-LED: 350mA @ 45V Max, 36 ~ 60V in

Manufacturer: STMicroelectronics

Whenever a lighting application, such as street lighting for example, requires an elevated number of LEDs, there are basically two solutions: the first is to connect all the diodes in series in a single "string"; the second is to place several strings in parallel with fewer elements in each one.

View Design

TPS61150EVM-150: 4 LEDs x 2 @ 15mA, 2.5 ~ 6V in

Manufacturer: Texas Instruments

The Texas Instruments TPS61150EVM-150 evaluation module contains the TPS61150 IC. This EVM provides two independently regulated current outputs using a single inductor step-up (boost) converter.

View Design

LM3404HVEVAL: 1A @ Vin Max, 6 ~ 75V in

Manufacturer: Texas Instruments

The LM3404HV circuit and BOM have been designed to provide a constant forward current of 1.0A to a single LED with a forward voltage of approximately 3.7V from an input of 48V ±10%. Over the input voltage range of 6V to 75V the average LED current, IF, is 1.0A ±10%, the ripple current, ΔiF, will not exceed 400 mAP-P, and the switching frequency is 200 kHz ± 10%.

View Design

ZXSC400EV4: 1 LED @ 350mA, 1.8 ~ 3 Vin

Manufacturer: Diodes Incorporated

The ZXSC400 is voltage mode boost converter in SOT23-6 package. Its low feedback voltage allows the current in a chain of LEDs to be set and accurately monitored with a single resistor with minimal losses. The ZXSC400EV4 is configured as a boost converter to drive a 1W LED from two NiCd / NiMH batteries.

View Design

STEVAL-ILL010V1: 1 ~ 6 LEDs @ 350 mA, 8 ~ 30V in

Manufacturer: STMicroelectronics

This evaluation board is designed around an L6902D-based DC-DC converter with dimming interface. The board implements both of two well known dimming methods: - Analog current control - Average current control by PWM

View Design

STEVAL-ILL007V1: 1 to 3 LEDs @ 0.35, 0.7, or 1A

Manufacturer: STMicroelectronics

The evaluation board is designed to display the full functionality of L5973D as a LED driver to drive one to three 1W, 3W as well as 5W LEDs at 12Vac input. The components selected for the demo board are optimized for 5W LED driver application.

View Design

LM3402EVAL: 350mA @ Vin Max, 6 ~ 42V in

Manufacturer: Texas Instruments

The LM3402 circuit and BOM have been designed to provide a constant forward current of 350 mA to a single LED with a forward voltage of approximately 3.5V. (Typical of white, blue, and green LEDs using InGaN technology.)

View Design
152 Results - Page 1/16 |< < 1 2 3 4 5 > >|